Jump to content
  TPR Home | Parks | Twitter | Facebook | YouTube | Instagram 

The Model Cyclone Racer


Recommended Posts

  • Replies 171
  • Created
  • Last Reply

Top Posters In This Topic

I am really happy. I recently discovered a couple of short cuts I can use to lay the Cyclone Racers sub track composite. Note that the model reflects the actual laminated on the bias boards. ESPECIALLY with the Airplane and all its spirals, this was no easy task.

 

But the Cyclone Racer is not quite so compact. My new process in making sub track cuts 70% off the time it used to, and does a much cleaner job. It also cut the time it takes to make the straight sub track by a little more than half!

 

I’m already out of little sticks for the track so I’ll just…have to work on something else.

IMG_20170810_211531103.thumb.jpg.8b62e3328ebcfbc0924690409ec091e4.jpg

Placing headers to help hold the structure up once the station goes underneath.

IMG_20170811_143623547.thumb.jpg.4c21693918a4364c159408db40f4f9bc.jpg

I started cutting through the center of the base of the turn around. This is where the station house will go.

IMG_20170813_081539871.thumb.jpg.90ec8ac7bcc0a2340fc1a8fbb3d23c43.jpg

Photo shows one almost-finished run of sub track spliced on to the extension.

IMG_20170813_081557882.thumb.jpg.3ef9998093f21485805825358a83708c.jpg

I now make the sub track off the structure. My fingers go from one end to the other making sharp little twists to give it that arc. Each run is 14” long and I can splice them together.

IMG_20170813_103055110.thumb.jpg.b5001eec06b38d95df7d0d19c40c953d.jpg

On the left run, the next layer of laminated 2x2’s (with the bias in the opposite direction as the bottom) have been added.

IMG_20170813_163235523.thumb.jpg.5e9ac7664bd12a15660b223b9e379384.jpg

I was really NOT looking forward to sub tracking these two lower runs because it’s about 42” around. BUT since I have my track making short cut, it won’t be bad at all. In fact…

IMG_20170813_163617959.thumb.jpg.10097f18fce34e4a7a9a65fdb0bedaa2.jpg

Another layer of boards are added on to the track and the catwalk boards are going in too.

IMG_20170813_164213495.thumb.jpg.e8ba323a11784761f24ee16005515db0.jpg

IMG_20170814_191555610.thumb.jpg.797500e8cda3d1fbfa27488a3a2a98db.jpg

Glam shot 1

IMG_20170814_191809411.thumb.jpg.4bc1d3019193f834af6853f03848d90c.jpg

Glam shot 2

IMG_20170814_224137867.thumb.jpg.1d718bb2cc80308fde933dc93d5dc2f5.jpg

I did all this in one day! Swiiiiish!

IMG_20170814_224801352.thumb.jpg.c6428207fd2c7fde8fb4da83067dc219.jpg

Swoooosh!

IMG_20170814_194349439.thumb.jpg.61d3ddc954a2cb7424a7c51976d9ca55.jpg

See the sub track sitting in the little troughs I made to keep them equally spaced while I put on the ties.

IMG_20170813_083823388_HDR.thumb.jpg.52f025c08899ace632781a1824afc700.jpg

I make what I call, The Spine of Ties. They are set up 3’ apart on center, so I simply just lay and glue the ties on to the curved sub track, and remove the spine. That way, the ties are 3’ apart on center.

Edited by hillflyer
Link to comment
Share on other sites

  • 2 weeks later...

The coaster is coming along well enough now so I’m feeling like I can sort of ramp up the promotion for my project and raise some more money. I’m working on a little brochure I can hand out to people too afraid to come up and ask me directly while I’m working.

 

At this point I’m making a little progress every day but at the end of each day it doesn’t look too different than it did in the morning.

IMG_20170819_221618.thumb.jpg.fa2257202b82a7ad36441b62602e35b2.jpg

I ran out of track material so while I was waiting a week for a shipment, I started making bents and section for what will be the exit from the north u-turn and the lower midcourse brake run.

IMG_20170829_223620.thumb.jpg.7302edd2d44080645861d0473e67be87.jpg

In a post from about a year ago, I mentioned I would be placing pins in the plastic to look like bolts in all the joints. After I did that with the prototype section and found it compromised rather than strengthened the structural integrity of the plastic.

 

So instead, I’m using a dremel to dot a tiny hole that I rub over with paint for this result. But I will still put pins in where the ledgers attach.

s-l225.jpg.e7820408857cc9f338785d7a2daae1b0.jpg

A new photo I found of this angle. I need all the help I can get to get this lower sweep of track just right.

IMG_20170824_132716277.thumb.jpg.903acf29ecadb6144531bfa654d4201f.jpg

New track material finally arrived. I started laying layer #3 on the left side while the track on the right inspires.

IMG_20170829_221159691.thumb.jpg.3dae9f2d0665bc721a033f09e3fd107f.jpg

Racing track. Catwalks too. I wonder if workmen ever challenged each other on foot over the catwalks?

IMG_20170820_084938089.thumb.jpg.fff56a9d10f6f76c9390dd98f264dd5e.jpg

Lining up new sub track for the mid brakes and the dip after.

IMG_20170828_075930461_HDR.thumb.jpg.3f0b27178ac7261112c4753c8869b155.jpg

A POV shot, testing to see if I need more ‘dirt and grease’ added.

IMG_20170825_141403782.thumb.jpg.001ec6db08b7e42b92250aa84a5eb5ec.jpg

I think I got that lower sweep of track right on!

IMG_20170829_221144892.thumb.jpg.3f59cfa183146215cd1974e39f9085ba.jpg

More racing track

IMG_20170829_221127654_HDR.thumb.jpg.157c8df7229e516fca8476afd66cb65c.jpg

All this built since mid-July!

IMG_20170827_214437202.thumb.jpg.c3b848f3e2ed9ef185ec2033c7febf9b.jpg

What it looks like in my work space at home

IMG_20170827_212938949_HDR.thumb.jpg.77d2fba50b6a7b4500a586b0d720a02c.jpg

Glam shot!

Link to comment
Share on other sites

Hello fans

 

Thanks for the large viewings of this thread and its photos.

 

I’m still trying to fund this project and I’m wondering if I can do that by selling a few.

 

Does anyone think some of the more artsy photos will be sellable to anyone, such as a poster, specifically coaster fans of course?

 

Maybe I’ll post a few and people can vote so I can get an idea of what people like?

 

I’ve been mostly working on track. It’s a good thing I shortened the process because…it’s sure time consuming.

 

Good news is this section took only two months in its entirety. The turn-around on the opposite end is a little larger and probably not as complicated as this end in spite of their being SIX runs of track and the switch rack.

 

I will probably work on that part during next summer’s vacation.

 

That gives be 8 months to do the in-between. That is mostly just tangent runs and those are a snap!

 

Tonight I begin attempting to fit it over the station. Wish me luck.

IMG_20170901_150701429.thumb.jpg.bed4535a8e739e0b8fb8322e46b4164f.jpg

Twice as hard and twice as fun.

IMG_20170904_120921778.thumb.jpg.a26eb048aa3b53f631995e81be87d80d.jpg

Racing trains would be heading towards you.

IMG_20170902_213107610.thumb.jpg.7d6862f053769ad9beb349360be50b5c.jpg

This is an example of what I was talking about ‘artsy’

IMG_20170905_222921717_HDR.thumb.jpg.c855ae5f465c3330ddc3ccc0bf818fd1.jpg

Another glam shot. I really like this effect of placing this on a mirror and shining a bright light into it.

IMG_20170904_184014317_HDR.thumb.jpg.29492682ff0fd92c3e8a51655895d9e8.jpg

The tracking is complete on this end.

IMG_20170906_215513011_HDR.thumb.jpg.c48a32033976e9d90e6e3a4869c30bd6.jpg

Last night I cut off all the posts that would be in the way of the station house. That is a strong suspension, I was a little worried about that.

Link to comment
Share on other sites

In commemoration for today, the 49th anniversary of the Cyclone Racer's last day of operation.

IMG_20170909_121136390.thumb.jpg.8f1c6f810f5b2add088a7b833d37782a.jpg

Last time I think I left us with a photo of a shot of a big hole in the middle of my turn around. I finally got the guts and tried setting it on top of the station house to test how it will fit.

IMG_20170909_121247150.thumb.jpg.17457be99b50be309b0bfad482c59712.jpg

The initial setting was good, the only difficulty was keeping track of all post clearings at one time.

IMG_20170908_220044028.thumb.jpg.3c9f8e227dfa89357134e0b7c3377758.jpg

I still need a good break from this section. I need to finish the inside of the station house before I can secure the roof before I can permanently affix the turn around. It sounds like a lot to do, and it might be, but I hope it’s not.

IMG_20170912_203152315.thumb.jpg.d709173bf97a405036f4d59ff4b0546d.jpg

So in the mean time I weaved together more sub track for the exit out of the u turn.

IMG_20170912_215407045.thumb.jpg.8aa57eda93a2e8b0c7a9ec888152cc9c.jpg

Underside shot of how it’s supposed to look.

IMG_20170912_215756063.thumb.jpg.46a3ef93952e198f86a8193fe43f5019.jpg

Topside shot, obviously.

IMG_20170909_125516461.thumb.jpg.2769ded98c385d0f543ea6dac3da4a6f.jpg

The midcourse brake area before adding the mechanics

IMG_20170912_215505208.thumb.jpg.ac28c1ab6aed573e212ded07a3855c79.jpg

The midcourse brake area after adding all the mechanics

IMG_20170913_221149262_HDR.thumb.jpg.1b145b0ca363bb25cb94b6ce5f9a2b94.jpg

Pictorial update.

CRdemo4.jpg.98ada5e3c7f9cbba89f47a064cdaa3f7.jpg

The end of the Cyclone Racer. The North end to be more specific lol.

Edited by hillflyer
Link to comment
Share on other sites

  • 2 weeks later...

The third annual Maker Faire is coming to Balboa Park 10/7 -8. Of course I’m working on having a certain part of the model Cyclone Racer finished by then. Jeepers, that’s only one week!

 

Since the last time…

IMG_20170918_163228262.thumb.jpg.eee5672f49d543b3b71b9cb3f91c0494.jpg

I’ve made a messy stack of bents that will support the remainder of the drop coming off the flat turn around over the Cyclone Racer sign, and the adjacent ramp up to the mid-coarse brake run.

IMG_20170918_163314761.thumb.jpg.9d1dc0933084430563536a77b4a23f69.jpg

Neating up the pile

IMG_20170918_194618564_HDR.thumb.jpg.70d68195a9e2a404eed226318aecedf4.jpg

Evenly spacing the bents while up on their side gives a nice flat look.

IMG_20170918_213330468.thumb.jpg.9a5aba0dfeb72601ee2b5ded80356abd.jpg

Installing ribbons

IMG_20170921_181520893.thumb.jpg.b42aff10b05882000b222977ec8206c6.jpg

The lower left portion (with temporary track on it) is the new section

IMG_20170923_133811221.thumb.jpg.d03115ec456ac94d4d74eedb3e58c308.jpg

Putting on the base for the real track.

IMG_20170924_123544040.thumb.jpg.865205b3af625c6dce68934054e6e725.jpg

Layer #5 is the ‘lip’ under which the train’s up-stop plates would fit. Two more layers of track will be applied here. The track next to that is up to the third layer of 2x2s set on the bias.

IMG_20170926_230519146.thumb.jpg.18d98aee6b29bf7b4241a79de7df9f1d.jpg

Thought I’d try a night shot.

IMG_20170920_152424176_HDR.thumb.jpg.181e0668b7a23bed109d3b6e23e4b1ab.jpg

Posts are cut for the opposite side of the flat turnaround. You can see the shape of the upper and lower runs of track.

CRnwgd60c.jpg.e02f156125db136cbae925539f4052a1.jpg

Basically, what you see is what I hope to have finished by Maker Faire.

Link to comment
Share on other sites

It’s my birthday today! I thought I’d post early just cuz of that.

 

This weekend is Maker Faire!

 

I will also be raising more funds to continue work on the model

IMG_20171001_172403499.thumb.jpg.880fb1195687a4f988848a2d6301ae86.jpg

Last weekend I tried using mahogany shelving paper to lay on what will be the model’s permanent base. I like the contrast of the darker base and later, can suggest that it’s a pier. I suck at spreading shelving paper, I think I can get that wrinkle out with some heat.

IMG_20171001_172417795_HDR.thumb.jpg.9c81d5d3923a448715ed89af86a87045.jpg

IMG_20171001_172433037_HDR.thumb.jpg.5108488704c8755a196817a82435e128.jpg

This section is overlaid with the drawing of the station house and both J turns to make sure it will align properly.

IMG_20171003_204524081_HDR.thumb.jpg.e68f254765e6935bad6cbe661428c55a.jpg

Brake sleds installed on the midcourse brake run.

IMG_20171002_223004559_HDR.thumb.jpg.7368354e54c3c980ebd486eacf319c1c.jpg

IMG_20171003_225823.thumb.jpg.3667bd6bba0d255f36df83bb94a6f377.jpg

Art shot

CRtmnwd4.thumb.jpg.541e928bb1c6f1efc30e52a1d2e7fb97.jpg

SKM_C25817100315360.thumb.jpg.534cc86739ce41ad689bd2d0680c0b14.jpg

SKM_C25817100410370.thumb.jpg.d6d59725049abd2ca100b1edebb04d5b.jpg

Link to comment
Share on other sites

  • 2 weeks later...

Another recognition honor at my 3rd year at the Annual Maker Faire.

IMG_20171017_223150419_HDR.thumb.jpg.2e657f6ec7c98f4c620d804ff1edbec7.jpg

The newest addition is the basic frame for the lead to the U-turn over the station house ® and the beginning of the final lap (l).

IMG_20171014_192731371.thumb.jpg.ed9309c69facbf9974cddd2f779655a3.jpg

Handmade sheets of catwalk and track base.

IMG_20171006_203848477.thumb.jpg.7bda7da04c9836d7bb145d734f3333f6.jpg

I was watching 2 Broke Girls the other night (guilty pleasure). One of the characters, Max, was chewing on a candy necklace and that reminded me that I once used a candy necklace for footings on a model I did in 1985 of the Belmont coaster.

IMG_20171006_205212045.thumb.jpg.c0d084780a50ceeb8b02c72a60f8f971.jpg

So I broke a few necklaces and spray painted them brown.

IMG_20171008_174935200_HDR.thumb.jpg.d1b8aebd345af108f548a3b72559d025.jpg

My blue ribbon and I at the Maker Faire

IMG_20171007_105834600.thumb.jpg.39d406ed2738fc9b065c38f2fef4fefa.jpg

I thought this was clever. While most people get the joke, very few REALLLLY get the joke.

IMG_20171017_074737847.thumb.jpg.75e718d0b31b853cfb134cf0fcc7de5c.jpg

With the newest portion added

IMG_20171017_074813564.thumb.jpg.02c4d070aac6f03ef5ef1e45937101dd.jpg

IMG_20171017_074702487.thumb.jpg.1af319d8fdde7bd52196493bd4e275a4.jpg

IMG_20171017_223418540_HDR.thumb.jpg.a756e6214db92e07ffc154426e13a2c7.jpg

The newest portion being fitted for track.

IMG_20171018_125437637.thumb.jpg.7d4131246394d5d24dddbd993df1caa0.jpg

Designing the profile for the next section to be built, hill #5 that carves under and through the lift hills. This area is going to be cross-over hell madness

CRtmF3.thumb.jpg.d5a47b68054c7d6705b7a05be72d2de2.jpg

The portion of the model that was displayed at the faire.

Edited by hillflyer
Link to comment
Share on other sites

  • 3 weeks later...

Track making, and building the flanks entering and exiting the flat turn over the station house.

IMG_20171021_123900643.thumb.jpg.c1fbbdddf4b1d8f760a61ee44dc5d1e9.jpg

Ugh. Time to weave some coaster track.

IMG_20171022_154116.thumb.jpg.e193c24ed1e0cc079043ce0f41554036.jpg

The big hill in the middle is the new track. The adjacent run on the right is about to get some.

IMG_20171023_212544550.thumb.jpg.c2f183a1e867d65311deb3fcc308fd5c.jpg

Subtrack on the right

IMG_20171023_212945737_HDR.thumb.jpg.e14f377a4e4703743699fa71cf00371b.jpg

A good shot of the under the track

IMG_20171027_202616057.thumb.jpg.57e31b85644d10a8b42d2aeb301ce1aa.jpg

A show and tell section of track that people can handle. I made it for the Maker Faire but lost it until recently.

IMG_20171027_220255703_HDR.thumb.jpg.1b2770b92084c8b699684e0ed595b0a8.jpg

Okay, here are a couple arty ones

IMG_20171028_100310.thumb.jpg.3b3000635a8fb0a190efacfeb8871214.jpg

IMG_20171101_172728657.thumb.jpg.6779e0561b733c7f5a3a4151e2e0fcdd.jpg

As of Wednesday, three sections before you.

IMG_20171101_172913824.thumb.jpg.ffef051c1a69193cde00eb7768f584df.jpg

Not pictured: The station house and lift hills

IMG_20171101_185438.thumb.jpg.9c33779e9ec5a0a3efdd4b054dcdc1df.jpg

Here are a few shots to fool your friends in a “guess the coaster” quiz

IMG_20171101_214740.thumb.jpg.007b91dd2684be1b12dd3ed84e8a941e.jpg

IMG_20171101_185600.thumb.jpg.7cc3f75c5e997a0e5a1f52cdc5ef7a5f.jpg

CRemg60.jpg.856eac48058c3134f1fa2c1864c44203.jpg

The hill buried way under the lift hill will be the next section to be built. It is REALLY buried inside and under the lift hill so it's hard to 'get in' there for a good view. Stay tuned for how I have figured out how to figure it out.

Edited by hillflyer
Link to comment
Share on other sites

  • 2 weeks later...

Trying to dissect the bulky middle portion of the Cyclone Racer, including the lift hills, the slicing hill, over the entrance to the brake run. Footings, some art shots of Airplane:

IMG_20171106_152644926.thumb.jpg.6a17a848355a6de5a7573bd724e9acce.jpg

I’m going to make a mini-test version. So I use plastic sticks to stick into where each vertical posts would touch the ground. The posts that wouldn’t touch the ground (or they would pierce the track) are colored red.

IMG_20171106_152657828.thumb.jpg.0f70146437791499a75171593f0d8e94.jpg

The red posts I know have to have some kind of header that will have to support it. Figuring out which posts are used to support other posts looks very challenging.

IMG_20171106_161131700.thumb.jpg.7eec45d632b6f6bfe65be41cda40127f.jpg

I added the black horizontal ledgers per the ones that I can see in the photos.

IMG_20171113_140338652_HDR.thumb.jpg.5970abf74c712efaf325114cc82e03a4.jpg

I simplified the plan for the midsection of the Cyclone and colored each path starting with the upper portion dominating over lower paths.

IMG_20171028_191858347_HDR.thumb.jpg.3a03ad3954f9cead29d4b4734bf656e5.jpg

When I link two sections together, splicing the track will be really easy compared to how I was doing it on the Airplane.

IMG_20171111_140401609.thumb.jpg.bdd025f18829a6ba7f3bd1d1c513a94a.jpg

Adding footings. Most of my work for the next three weeks will be affixing all three sections on to the station house base. That is one of the lift hills. This section with footings will overlap the lift hill.

IMG_20171110_155500093_HDR.thumb.jpg.1d9b2468ace9d1cab131909678d95f13.jpg

When I link two sections together, splicing the track will be really easy compared to how I was doing it on the Airplane.

IMG_20171110_173609.jpg.ac1d7a116bd5d269ba2eb4e0cd4bace0.jpg

A little cleanup is necessary but otherwise, very close with the film frame below.

IMG_20171112_160008388_HDR.thumb.jpg.4c02e4c3dab535632a6c8a8ee0fac4ef.jpg

IMG_20171111_193823815.thumb.jpg.7018fa467f0ec42805cdc05532111a8e.jpg

Test fitting the opposite side. In the foreground is the hill that leads up to the turnaround.

IMG_20171112_125358074.thumb.jpg.00270dba0d72f06bb6cd93f8103f8582.jpg

IMG_20170716_211058.thumb.jpg.6d3cf74f07d389045361aca189d475a7.jpg

A couple of Airplane photos

IMG_20170902_180346.thumb.jpg.808d9cc6370728bf0915321e5067022f.jpg

You can expect to see this shot again once I add the handrails

IMG_20171104_122230414.thumb.jpg.c1f6081b364f624069a8e58d3ba65203.jpg

All the glue I’ve used thus far

IMG_20171110_161357.thumb.jpg.66412701de3b19bb950b32ae22f7b986.jpg

I love this one

IMG_20171112_091322.thumb.jpg.ef50d4bc3497bc4e7584daf3b1fd2f49.jpg

289747604_CRfpovr1(3).thumb.png.ab7424536663cc343a1de12612c6cd8e.png

From "Strike Me Pink."

CRea40.png.1c66af37534c4827c1a0e8d844bebe4a.png

Here is the area I'm trying to reassemble. You can see two hill tops that seem to appear buried under the lift hill, but it's the one

CRfih5pov.thumb.png.8de2a660066875716376a8caaf3ba3aa.png

The best source for this area is a shaky, but nice, POV footage used in the 1964 Cult classic, "The Incredibly Strange Creatures Who Died and Became Mixed Up Zombies."

CRfih5pov2.thumb.png.bb1b9d5f35012dcb19832b9cdf113a17.png

For the supports that cannot be discovered in any clear photo of film frame, my best educated guess will have to do. And from someone familiar with Fred Church’s tricks, that will be a real bona fide educated guess.

Edited by hillflyer
Link to comment
Share on other sites

  • 2 weeks later...

Station house detail shots, and what I call 'the gear box' actually, the sprocket wheel at the turning point of the lift chain.

IMG_20171118_114629267.thumb.jpg.5b0ab9865b27df0b474f7a09f1ace098.jpg

The bottom of one of the lift hills. Here is where I need to install some sort of home for the bottom return wheel for the drag chain.

IMG_20171118_161748423.thumb.jpg.6597914ad4f7ee6cb7195d00ff774ef3.jpg

So I started by making a little gear thingy. While the bottom wheel probably had a groove, I think my cog wheel will be just fine.

IMG_20171118_161804599.thumb.jpg.691984e897e6317e20eaec33e74111b2.jpg

Then I made a couple of boxes. I tried to make them look like they've been in use for about 10 years

IMG_20171118_194511334_HDR.thumb.jpg.f1b8ee2597ff1cf428ab2c980d3a2261.jpg

All this trouble and NOBODY is going to see it except for my followers!!

IMG_20171120_222907165.thumb.jpg.d4c0c994ec6740a01accd3e34c087e7f.jpg

I LOVE my brake handle. The foot catch is an accidental shaving of plastic as is the little hand grasp.

IMG_20171120_223011647.thumb.jpg.d3a19dc4c6878751422b6a82d697291e.jpg

Prior and Church transfer tables always had nicely carved levers.

IMG_20171124_204811.thumb.jpg.7251d13705b0bfc32c4c66ea57e1c58f.jpg

Drama

IMG_20171125_142539648_HDR.thumb.jpg.16dccbafd285f8d2d02db0a0a98b42c3.jpg

The train release handles

IMG_20171125_152434527.thumb.jpg.86ab704017eb7371cffd8c8890d530ee.jpg

Handrails down the exit stairway

IMG_20171126_191141712.thumb.jpg.530a31fcbfeedcd3929a46f75b66f3f7.jpg

back to the drawing board.

IMG_20171126_200329301.thumb.jpg.fc3d21bb1987a403f6a1ee8dcc6ab3b1.jpg

Much much better. Time to paint.

IMG_20171125_142221025.thumb.jpg.73c23affad940d14aaf373fb8854e5e5.jpg

A little funny photo of me playing inside the station. “Everyone hold on!!”

 

This photo (if you look way in the back, the red side rails wobble) caused me to rethink how my side rails alongside the station line up. They don’t to my satisfaction so

Edited by hillflyer
Link to comment
Share on other sites

  • 2 weeks later...

Getting recognized for my research into old historic roller coasters and bringing them back so all may see just now beautiful they were and for my contribution of those models to the National Roller Coaster Museum with an ACE honorary membership! Also recognized for guaranteeing the Giant Dipper would not be torn down.

IMG_20171201_203215966_HDR.thumb.jpg.a60b05f2f63bb716bc90552468ebc9a1.jpg

Finally, finally, FINALLY attached the roof on to the station house.

IMG_20171202_154700538.thumb.jpg.7ce1a559d872c86c29e193b1f8c941df.jpg

Underside of station house

IMG_20171202_215632859.thumb.jpg.0e84b2a047e5eabbb3e4ed2125c03008.jpg

Approach to lift hill B.

IMG_20171202_221542875.thumb.jpg.7d3e21bd5595ad24c18442bd628aebe0.jpg

These are random shots that I won’t be able to get once I add the U turn.

IMG_20171203_142217742.thumb.jpg.bd9bfabf6ce584beeb1405e38859a191.jpg

The bottom wheel for the chain

IMG_20171204_075145.thumb.jpg.fe476e9ec798140d6483e28786199f38.jpg

Some artsy ones

IMG_20171204_132050.thumb.jpg.48f5992d71638579541582ba7ba53503.jpg

Some artsy ones

IMG_20171207_151039853.thumb.jpg.261058857864212f35e68ee447f5554d.jpg

Oh lookie! I think I made the train chassis about a year ago. Finally took them off the shelf.

IMG_20171208_075012256.thumb.jpg.37f7bb7b64a88986aba6ff19d9a25a39.jpg

Approach to the station

IMG_20171208_153051362_HDR.thumb.jpg.184138e1daaea5dfeed65fa76f1851a9.jpg

These make me think of macaroni shells as they feel just like them.

IMG_20171208_153209171_HDR.thumb.jpg.087d111a75e8757574f274bc3a57b44d.jpg

Cyclone Racer trains were near exactly like the ones that used to run on Playland’s Dragon.

IMG_20171209_090814798.thumb.jpg.6eda1e137bd2634bc00d4f41ef0517b6.jpg

Chug chug

IMG_20171209_142020975.thumb.jpg.5a8b039c9fc76ea15bf9dadd01718112.jpg

One area I want to be really careful with tracking curves like this – I’ve been a little afraid to start. Laying curved track can affect the structure because of the collective bending of the laminates so I'm using part of a chain off of Ghostrider for a good weight.

IMG_20171209_222807.thumb.jpg.8fba7f6298f97f56a7b8228c3f00de54.jpg

Perfect.

IMG_20171210_125616.thumb.jpg.99a6a978a606cdb04fc3ca2f5558961f.jpg

Not too bad. I’m satisfied that each side looks the same.

IMG_20171210_160313627_HDR.thumb.jpg.0a1a6a8c460668e6ef9df06e87451a64.jpg

What an honor. Jerry Willard was the presenter. Host John Gerard is the one with the long beard.

IMG_20171211_131133044.thumb.jpg.ad60f23a892a3bdf538eec7df81d6b0b.jpg

I heard ACE has been meaning to give this to me since the spring but I never appear at any cost-prohibitive ACE events. This timing makes it my best Christmas present! Now, on to Cyclone Racer:

IMG_20171208_175648446.thumb.jpg.44289d066689a3a3bb50fe7849448bc1.jpg

Ghost train skidding home.

IMG_20171209_220628464.thumb.jpg.2d49397d83028fa4384f47c78b9ddb6a.jpg

Not only the banking, but the elevation too. It was tricky getting that subtle little hump going down from around the curve into that low dip.

IMG_20171210_164105369.thumb.jpg.5b13eb265c976c5617ae153bba349285.jpg

Fred Church was a genius

IMG_20171210_164120486.thumb.jpg.217a5f89895fb252e2279013c63bafa6.jpg

I showed this to someone at the party and he thought it was the real thing. I didn't know he thought that until I was showing someone else.

Edited by hillflyer
Link to comment
Share on other sites

  • 3 weeks later...

.

IMG_20171222_100221074_HDR.thumb.jpg.56084b67c0f575e8845eadd74dc09a67.jpg

Cutting sticks against profile design.

IMG_20171228_215251706_HDR.thumb.jpg.b43c48d970add75c0166e1e0dbaf93d8.jpg

The final dip before leaping up to the brakes. The tall supports are to help support upper structure. The bent with the 3 clothes pins is the bottom part of the tallest lift hill bent.

IMG_20171228_222234900_HDR.thumb.jpg.d3794b99ac400ae18e55f67324a60e0c.jpg

Did a little paint job on the cars.

Edited by hillflyer
Link to comment
Share on other sites

  • 2 weeks later...

LONG OVERDUE UPDATE SOON

IMG_20171231_102123068.thumb.jpg.fc59b615319de8f20b0805e50c858a67.jpg

Then I built the next layer of structure above – that hill in the middle of the ride that zig zags under the left hills.

IMG_20171231_152754632.thumb.jpg.ba4b17a527349337c9890ac6fbd6599e.jpg

And I took that part and did a test fit over the low part.

IMG_20180101_150454987.thumb.jpg.330ec226c9f1f1a1179ae1da2e58dffb.jpg

Sub track made and ready to lay!

IMG_20180101_151824402.thumb.jpg.8afd96f685ebab2662f76f6230ef05bb.jpg

Beautiful fit.

IMG_20180102_161258189_HDR.thumb.jpg.ce746f8cfb1e0025d2c47d05bb275b7f.jpg

IMG_20180102_161313378.thumb.jpg.49624c689c0f80439dcd1ddfbcb53ccd.jpg

IMG_20180103_144203296.thumb.jpg.b37c7cdc050d25046db7330cfa64d754.jpg

More lift hill bents. The tallest six bents have been built.

IMG_20180104_211432368.thumb.jpg.89d003bab84fdc7393357436f91d197e.jpg

And added. This is only the East lift hill. 6 duplicate bents are built, not shown.

IMG_20180105_151722360.thumb.jpg.e109247e6cefd5dc8663c5b7b38a4804.jpg

This picture is proof, that even on areas that are in the deepest bowels within the wood structure, I spared no attention to detail, even laminating the mid-layer of track that nobody will ever see.

IMG_20180105_175241417.thumb.jpg.71d2ca6c0facc325922d8018f50ef1cc.jpg

Also while on vacation, I created a little more space in my work corner along with some rearranging of my living room.

IMG_20180105_175707526.thumb.jpg.2009f03c12d685a7a0b944b57296ddb8.jpg

The unexpected outcome was a nice roller coaster shadow on my wall!

IMG_20180107_155945237.thumb.jpg.317c66b5f5a65f1543b4cf97b64f1375.jpg

My handrails are notched around the lateral cross braces. Again, only people seeing this photo will see this deep in the ride.

IMG_20180107_161955787.thumb.jpg.19d4210520d2677b558f2f65e18419be.jpg

Track layers creeping up into the final brake section

IMG_20180107_165920985.thumb.jpg.e0b9b4b03ee70662c91cdf8b4d533df0.jpg

IMG_20180107_210107725.thumb.jpg.0e1795bf9805ed02b57a579fde52b502.jpg

IMG_20180107_165800698_HDR.thumb.jpg.c79c7620845e13714ac3a113695b784b.jpg

I set everything where it should set and added the supporting headers. To double check my accuracy, I took this shot to get an initial comparison to the real one. Until after I post this, I haven’t done that comparison. Note that the stacks of structure are not connected and still come apart in three pieces, accounting for some sticks that look like they're leaning.

CRibrakes.jpg.036493ab88b74fabdcc32ff0ee7517b9.jpg

Link to comment
Share on other sites

  • 3 months later...

Hi everyone,

 

First of all I want to dedicate this post to my best friend, Dan Reed, who was crossing a clearly marked intersection and was hit and killed by an errant driver last January right after his 50th birthday. Ironically, while I'm really passionate and eager to educate people to the dangers of distracted driving, so goes the same for distracted walking. He was probably looking at his phone and stoned out of his gourd, the driver was still at fault.

 

There hasn't been a post on here since then, I guess I was affected beyond what I thought.

 

Well, below is an update on the building of the model Cyclone Racer. It's coming along fantastic and this may be enough photos to warrant two separate postings.

tprDan.thumb.jpg.5778f4840799c4c928bcf237e589bb35.jpg

R.I.P. my best friend Dan Reed whose photo sits on what was his favorite chair when he came to visit. Okay, on to the Cyclone Racer.

1391.thumb.jpg.70046dbb489e60bd6ccafdbdf193c80f.jpg

Last we left, I had the main northern third including the station house, near completion. Here are the starts of the next main portion including the dip up into the brakes, part of the first drop, the nice round hill buried under the lift hills, two portions of that visible as well.

1397.thumb.jpg.63dd6d931ddc4734d2585c9151b33bc9.jpg

Buuzzzzzz, tap tap tap, saw saw, hammer hammer. Almost looks like a real construction at first as it begins to piece together.

CRfsr2.thumb.png.50a81def8f91df9bdddfed2acdda42e1.png

The next part to figure out and build is the valley of the first drop where it dives under the valley of the second drop. LOTS of mixing it up in this area.

1563.thumb.jpg.e3f012755e70f7be765d2a8c6943cc71.jpg

So first thing I did was build a 1/2 scale (from the model scale) rough over the plan so I could get 3D visual so I could better figure out how the bents and headers were designed.

1652.thumb.jpg.b81911ac95cbd406730411db54dc0163.jpg

Moving from mock-up to actual model, that area under the first drop is very heavy in terms of timber concentration!

1744.thumb.jpg.e972118e4f498ebfbce5caffe384b1ca.jpg

The rise up to the third hill is ready to install. But not yet.

1448.thumb.jpg.a4292ff00bcdf208913d6dab93e78986.jpg

Lift hill tracks made for the crest over the lift and down the first drop.

1661.thumb.jpg.40b04c3203607e4b20065f2f6320c72e.jpg

Slapped that track right on there.

1590.thumb.jpg.0f66b21b8e4813decd3392eb9dd15d52.jpg

I stopped doing professional style drawings. Notes and sketches are all I really need.

080.thumb.jpg.9d77ff1a89e275492c577b74a92f480c.jpg

The next few are shots I took this weekend when Gary Kyriazi came to visit me. He wrote, "The Great American Amusement Parks" book in 1976. This book is responsible for dying the coaster fever into my wool.

064.thumb.jpg.73e18d9fdc279eaa883be69516fcff50.jpg

All the gaps are not filled in yet.

066.thumb.jpg.63eb36853058ca51959db97202eb41a2.jpg

074.thumb.jpg.0c9259372ea5996a0fbfd8beb5dbc4d2.jpg

081.thumb.jpg.4494d431bad4279aaf6a9b731f5252ed.jpg

067.thumb.jpg.49cb479f99a394058a29f7cc868c5674.jpg

059.thumb.jpg.ed0aeb6d2abfb7d3a1ccd2da66516098.jpg

020.thumb.jpg.067f0921e0a1f8d5b8b944d895f18423.jpg

027.thumb.jpg.8e7251ea5770fbd3cddd9ce340337a5e.jpg

Good night. Until next time.

Link to comment
Share on other sites

  • 2 months later...
  • 3 weeks later...

Not too much to update. Had about a week to redo something I did wrong, but check out a rendering of a table and case I'd like to add.

IMG_20180724_071201744.thumb.jpg.f237c4097db5adea3e5d1934c2806004.jpg

The right pair of track - The mysterious 'split' where trains a and b switch sides

IMG_20180723_203526792.thumb.jpg.7e02366ac94bd150905ba669a55a3b70.jpg

The mysterious 'split' where trains a and b switch sides - using photo above to get all the details.

IMG_20180715_204602987.thumb.jpg.821727b1def00a302c93dc8a982364a6.jpg

A little more fudging to do, but otherwise, fairly convincing

IMG_20180729_201055287.thumb.jpg.d378c8e0aefb84e687e2b3ffb0a51956.jpg

Not EVEN Colossus....

IMG_20180729_202610309_HDR.thumb.jpg.7f2d61a67c205f2fd27d3473f326a1a5.jpg

December or January?

FB_IMG_1533067858427.jpg.0be881e0953d12737693aee2a4cba918.jpg

The case I've designed for the finished model. I'm hoping to find someone who will build it for $500

CRfswd7.png.ceabb42c917de9baa6d1d3cb82f86306.png

What it's supposed to look like. Please excuse my notes.

Link to comment
Share on other sites

  • 2 weeks later...

An update on where the model stands in terms of construction. Don't be fooled, the parts I'm saving for last are uber easy. Once I finish that turn....Blue lines are track that exists on the model, the red are bents that are up, just not tracked yet.

2111088324_CRmap.thumb.png.0c5731d8504390b1397cf3a875c85242.png

crtmh14.thumb.jpg.0557c90f4c2b02940453f873211dcc37.jpg

Art shot. Would be August in a calendar.

Link to comment
Share on other sites

  • 3 weeks later...

Looking excellent! Your models are impressive!

 

That geometry drawing takes me back the 80s... looking at roller coaster pictures and magazines/books with a protractor, figuring out angles and super-geeky stuff.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    • No registered users viewing this page.

×
×
  • Create New...

Important Information

Terms of Use https://themeparkreview.com/forum/topic/116-terms-of-service-please-read/